Download NTPC Technical Question Paper

Books For Preparation


part 1


46. addition of a zero to a 2nd order underdamped system results in increase/decrease of rise time and increase/decrease of peak overshoot.

47. for PI ctrl we obtain improved bandwidth/improved steady state performance/ worsened steady state performance/

48. SNR of normal AM system is comparable/3 dB lower/3 dB higher/6 dB lower over DSB-SC and SSB system.

49. which is an effective measure of the noise related performance of an amplifier: SNR/noise ratio/thermal noise/shot noise.

50. given baseband signal freq and carrier freq calc which of the freq given will not be present for conventional AM.

51. distinction between FM and PM at high frequencies.

52. which of these has the least propagation delay RTL/ECL/I2L/CMOS.

53 switching speed of CMOS is affected/unaffected by changes in supply voltage.

54. which of these provides a measure of heart rate P/QRS complex/T/none of these.

55. given a ckt of a logarithmic amplifier you had to identify what ckt was it.

56. JFET can operate in depletion/enhancement/both/none of the above modes.

57. when a BJT operates in saturation the junctions are fwd biased/reverse biased/

58. BIBO stability criterion implies that poles are within/outside/on the unit circle.

59. for faithful amplification of low amplitude signals the cut-off/active/saturation regions of a transistor is used.

60. lissajous pattern of a signal rotates 36 times per minute. if the oscillator frequency is 560 kHz then the unknown freq is

61. % resolution of a 10 bit ADC.

62. to obtain 10 mV resolution on 5 V range how many bit DAC is to be used..

63. why is LCD preferred to LED.

64. how will 0.6973 be displayed on 10 V range of a 4 digit multimeter.

65. which of the following cannot be used for an automatic feedback temp ctrl system thermocouple/thermometer/thermistor/IC sensor.

66. y(n)=x(-n+3) is an example of a linear/non linear and shift variant/invariant system.

67. the falling body method is used to determine viscosity/humidity/.

68. which of these methods of viscosity measurement gives greatest accuracy falling body method/rotating cylinder method/both/

69. some question on gas chromatography

70.a device having a rotor with 3 Y-connected coils and a stator is likely to be a synchro/RVDT/control transformer/

71. in a twisted ring counter the initial count is 1000. after the 4th clock pulse its state will be.

72. a 240 kHz signal is given into a 3 bit binary ripple counter. The lowest o/p freq obtainable is.

73. for parity bit checking which of the following gates can be used XOR/NAND/OR/XNOR.

74. why is a BJT called so..

75. identify the expression for gauge factor of a strain gauge among the given options.

76. in a semiconductor strain gauge as tensile strain is applied what changes take place in the n and p areas..

77. how does a radioactive level gauging system work

78. a capacitive transducer measuring level works on the principle of change in distance between plates/change in dielectric strength/

79. for maximum power transfer in an AC circuit the condition to be satisfied is ZL+ZS=0/XL+XS=0/none of these/.where l and s refers to load and source resp.

80. find the transfer function from a block diagram.

81. synchronous ctrs are preferred to asynchronous ctrs bcoz they are faster/glitches at the output can be avoided/both/none of these.

82. the lissajous figure formed on an oscilloscope looks like the English figure of 8. if the vertical channel input is 1 kHz the horizontal input freq is.

83. IE=IC for a transistor in saturation/cutoff/active/both saturation and active regions.

84. reproducibility of measurements is called accuracy/precision/linearity/none of these.

85. which of these is not strictly a static characteristic accuracy/precision/tolerance/linearity.

86. the shunt coil in a Q meter has resistance of the order of m?/?/k?/..

87. for measuring inductance of high Q coils the bridge used is Maxwell-wien/Schering/

88. which of these measures inductance in terms of capacitance Maxwell and hay/Maxwell and Schering/hay and Schering/

89. in a flip-flop with preset and clear inputs both are applied simultaneously/clear is cleared when preset is applied/preset is cleared when clear is applied/.

90. what happens when the RET instruction is encountered by 8085

91. a 1024*8 memory chip needs how many address lines

92. what happens when the PUSH instruction is encountered by 8051.

93. in FM relation between no of sidebands w.r.t. modulating freq

94. numerical on DPSK.

95. a multiplexer accepts input data and provides one output all the time/one output at a time/many outputs at a time/many outputs all the time.

96. pulse modulation is essentially a process of multiplexing/.

97. wave shape is altered by clipper/clamper/voltage doubler/amplifier.

98. 4 signals of frequencies 100,100,200 and 400 Hz are sampled at nyquist rate and sent through TDM on a channel.the bandwidth of the channel is

99. superposition can be applied to a ckt with initial conditions/non-linear ckt/

100. kelvins double bridge is used for the measurement of

101. which of these is not an active transducer thermocouple/solar cell/RTD/none of these.

102. oscillator using positive feedback has gain of 0/?/undefined value/

103. wien bridge oscillator should initially have closed loop gain >3/<3/=3/

104. some question on gain margin and phase shift of a system.

105. fourier series expansion of even function has sine terms only/cosine terms only/no odd harmonics/

106. full wave rectifier gives clean dc o/p/dc o/p with small ripple/positive half and inverted negative half of i/p as o/p.

107. which of these values of ? gives damped oscillations: 0/1/1.6/0.6

108. for a transformer of ratio 1:a and excited by a source V with impedances Z1 and Z2 on the primary and secondary side value of a for maxm power transfer should be..

109. fourier transform of cos(?0t) is

110. at t=0 the step response of a 1st order system is.

111. 555 can be used as a monostable/astable/freq dividing ckt/all of these.

112. in a PT when the secondary is open ckted with the primary excited what will happen.

113. if a system is marginally stable then the nature of oscillations will be

114. linear encoders mostly use straight binary/BCD/gray code.

115. for an accelerometer working in displacement mode the ratio of forcing freq to natural freq should be..





NTPC Previous Year Solved Question Papers and Reference Books

1 comment:

Unknown said...

send me previous question paper please
my email id- mahzam9@gmail.com

thank you

Post a Comment

Followers